Max Brenner
PASS W/ CONDITIONSFriday, June 29, 2018 at 3:44 PM
Violations Cited
20-4-703.11
Food Contact Surfaces Clean
High temp dish machine rinse reading 160F.Repair. Maintain rinse 180-194F or per manufactures instructions. Wash reading 140F.Maintain minimum150F
Why This Matters
INVISIBLE KILLERS: Bacteria survive on 'clean-looking' surfaces for days. Inadequate sanitization caused Salmonella outbreak affecting 1,500 people via ice cream. Cutting boards can harbor 200 times more fecal bacteria than toilet seats. E. coli survives 1-4 hours on surfaces. Norovirus survives 2 weeks. One contaminated slicer infected 300 people with Listeria.
Code Requirements
SANITIZATION MANDATORY: Chemical sanitizers: Chlorine 50-100 ppm, Quaternary Ammonium 200-400 ppm, Iodine 12.5-25 ppm; Hot water: 171°F for 30 seconds by immersion; Contact time: minimum 7-30 seconds depending on sanitizer; Test concentration EVERY 2 hours; Change solution when visibly soiled; ALL food contact surfaces must be sanitized: After each use with different foods; When switching raw to ready-to-eat; Every 4 hours in continuous use.
Corrective Actions
IMMEDIATE: Set up proper sanitizer at ALL stations; Test and adjust concentration NOW; Re-sanitize ALL food contact surfaces; Obtain test strips immediately; Post sanitizer concentration chart; Train staff on test strip use; Create sanitization log; Change solutions every 2 hours minimum
22-4-601/602.11
Food Contact Surfaces Clean
Interior panel of ice machine soiled & observed with rusty screw. Clean to remove soils Replace screw.
Why This Matters
BIOFILM FORMATION: Visible soil indicates biofilms - communities of bacteria protected by slime layers that resist sanitizers. Biofilms on slicers have caused Listeria outbreaks killing 30% of victims. Meat slicer contamination sickened 300 across 6 states. Grease harbors Listeria which grows at refrigeration temperatures.
Code Requirements
Food contact surfaces must be: Visibly clean with no food debris; Free of grease accumulation; Smooth and cleanable; Cleaned and sanitized after each use; Cleaned every 4 hours if in continuous use; Equipment must be disassembled for cleaning when necessary.
Corrective Actions
Clean and sanitize ALL equipment immediately; Disassemble equipment for thorough cleaning; Establish cleaning schedule with assigned responsibilities; Use cleaning checklist; Train on proper disassembly; Increase cleaning frequency
02-3-602.11-.12/3-302.12
Food Container Labels
Provide labels on all bulk storage bins.
Why This Matters
Improper labeling can lead to using wrong or expired ingredients
Code Requirements
Immediate correction required. Follow health code section . Implement proper food labeling procedures. Train all staff. Document corrective actions taken.
14-4-202.11
Food Contact Surfaces Design
Bulk storage bins observed broken & in disrepair.Replace
Why This Matters
This violation affects overall sanitation and food safety
Code Requirements
Immediate correction required. Follow health code section . Implement proper food safety procedures. Train all staff. Document corrective actions taken.
15-4-202.16
Non-Food Contact Surfaces
Provide drip hose for soda gun. Dish room: Mechanical sanitizer dispenser not operating.Repair PIC to manuelly prepare Quats sanitizer until fixed. PIC to train & monitor staff with regards to preparing the sanitizer
Why This Matters
This violation affects overall sanitation and food safety
Code Requirements
Immediate correction required. Follow health code section . Implement proper food safety procedures. Train all staff. Document corrective actions taken.
17-4-204.112/.115
Equipment Thermometers
Provide internal thermometer in cook line 4 door unit.
Why This Matters
This violation affects overall sanitation and food safety
Code Requirements
Immediate correction required. Follow health code section . Implement proper equipment procedures. Train all staff. Document corrective actions taken.
23-4-602.13
Non-Food Contact Surfaces Clean
Clean interior gaskets of reach in units to remove spills & soils. Clean dust from large floor fan in prep room. Clean dust from storage jars on shelves in service area
Why This Matters
INDIRECT CONTAMINATION: Dirty surfaces attract pests, harbor bacteria, and contaminate via contact or air movement. Dust from dirty shelves contains allergens affecting 32 million Americans. Grease accumulation creates slip hazards causing 25% of restaurant injuries.
Code Requirements
Non-food contact surfaces must be cleaned at frequency to prevent: Soil accumulation; Pest attraction; Contamination of food/food contact surfaces. Includes: Equipment exteriors; Shelving; Walls and ceilings; Light fixtures; Ventilation systems.
Corrective Actions
Deep clean all non-food contact surfaces; Create cleaning schedule with daily, weekly, monthly tasks; Assign cleaning zones to staff; Use degreaser for grease accumulation; Clean from top to bottom; Maintain cleaning log
29-5-201/02.11
Installed and Maintained
Prep room handsink observed clogged.Repair
Why This Matters
This violation affects overall sanitation and food safety
Code Requirements
Immediate correction required. Follow health code section . Implement proper food safety procedures. Train all staff. Document corrective actions taken.
37-6-501.11-.12
Improper Maintenance of Walls/Ceilings
Wall at service area observed with worn paint.Repair Maintain smooth/durable/cleanable surface Upon re-inspection PIC was correcting
Why This Matters
OVERHEAD CONTAMINATION: Peeling paint and debris fall into food. Condensation on ceilings drips bacteria onto prep surfaces. Studies found ceiling tiles harbor Bacillus cereus spores. Restaurant ceiling collapse contaminated food service for 200 guests.
Code Requirements
Walls/ceilings must be: Smooth and washable in food areas; Light-colored for easy soil detection; Free of holes, cracks, peeling paint; Sealed at all joints and attachments; Clean and free of grease, dust, cobwebs; Non-absorbent in areas subject to moisture.
Corrective Actions
Repair all holes within 14 days; Repaint with washable paint; Replace damaged ceiling tiles; Seal all penetrations; Clean walls and ceilings monthly; Fix any leaks immediately; Install FRP panels in splash zones